Open Stack

http://docs.openstack.org/trunk/config-reference/content/section_compute-hypervisors.html
 has configuration entries for each hypervisor type.


On Thu, Jun 26, 2014 at 12:06 PM, O'Reilly, Dan <Daniel.OReilly at dish.com>
wrote:

> OK.  So, next question is the specific configuration for each compute
> node.  Do you know if there are sample configurations (e.g., nova.conf)
> available for these?
>
>
>
> Thanks!
>
>
>
> *From:* Andrew Mann [mailto:andrew at divvycloud.com]
> *Sent:* Thursday, June 26, 2014 10:22 AM
> *To:* O'Reilly, Dan
> *Cc:* openstack at lists.openstack.org
> *Subject:* Re: [Openstack] Architectural question
>
>
>
> Dan,
>
>
>
> If I understand your question properly, you can do this from the Horizon
> management web interface as an admin user. Under Admin->System Panel->Host
> Aggregates setup 3 aggregates each in their own availability zone, and then
> assign each host into a corresponding aggregate.
>
>
>
> I don't think the controller node needs any special configuration, and the
> compute nodes should just need the configuration to use the specific
> hypervisor you want on that host.  Each compute node must be running before
> it can be added to the host aggregate through the UI.
>
>
>
>
>
> On Thu, Jun 26, 2014 at 10:45 AM, O'Reilly, Dan <Daniel.OReilly at dish.com>
> wrote:
>
> I’m building a cloud and have a question about architecture/viability.
> Right now, I have the following configuration:
>
>
>
> -          Controller node running RHEL 6.5
>
> -          Network node running RHEL 6.5
>
> -          5 node Ceph cluster for block and object storage
>
> -          3 compute nodes:
>
> o   1 running RHEL 6.5 and VMware as the hypervisor
>
> o   1 running RHEL 6.5 and KVM as the hypervisor
>
> o   1 running CentOS 6.5 and Xen as the hypervisor
>
>
>
> The basic question is on the compute nodes.  I’m doing 3 different
> hypervisors to do a best-of-breed study (each will be in its own
> availability zone).  Hence, one of each type.  But is it even possible to
> have 3 compute nodes like this, and if so, how do I configure the compute
> software that runs on the controller node to handle this; and how do I
> configure each of the 3 compute nodes as well?
>
>
>
> Dan O'Reilly
>
> UNIX Systems Administration
>
> [image: cid:638154011 at 09122011-048B]
>
> 9601 S. Meridian Blvd.
>
> Englewood, CO 80112
>
> 720-514-6293
>
>
>
>
>
>
> _______________________________________________
> Mailing list:
> http://lists.openstack.org/cgi-bin/mailman/listinfo/openstack
> Post to     : openstack at lists.openstack.org
> Unsubscribe :
> http://lists.openstack.org/cgi-bin/mailman/listinfo/openstack
>
>
>
>
>
> --
>
> Andrew Mann
>
> DivvyCloud Inc.
>
> www.divvycloud.com
>



-- 
Andrew Mann
DivvyCloud Inc.
www.divvycloud.com
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.openstack.org/pipermail/openstack/attachments/20140626/a8746282/attachment.html>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: image001.jpg
Type: image/jpeg
Size: 1895 bytes
Desc: not available
URL: <http://lists.openstack.org/pipermail/openstack/attachments/20140626/a8746282/attachment.jpg>