[Openstack] Cant ping private or floating IP
Sylvain Bauza
sylvain.bauza at digimind.com
Fri Feb 22 11:29:13 UTC 2013
Let me clarify, you have :
-ARP cache entry for 10.5.5.1 on 10.5.5.5
-ARP cache entry for 10.5.5.5 on 10.5.5.1
with correct MAC addresses (make sure with 'ip a show qr-XXXX') and ICMP
request is still not visible on 10.5.5.5 with 'tcpdump -i eth0 -nn icmp' ?
If yes, I have to admit I can't help you further. I saw you were using
virtual alias eth0.2, maybe it's the root cause.
All my setup is based on physical network cards, I haven't created
virtual aliases and this basic test works. You have trouble with L2 and
I don't think Quantum is responsible of that.
-Sylvain
Le 22/02/2013 11:50, Chathura M. Sarathchandra Magurawalage a écrit :
> I tried tcpdump on 10.5.5.5 while pinging but I can' t see ICMP
> requests :(
>
> And I do have right ARP entries on 10.5.5.5
>
> Thanks.
>
>
> On 22 February 2013 08:21, Sylvain Bauza <sylvain.bauza at digimind.com
> <mailto:sylvain.bauza at digimind.com>> wrote:
>
> As per you mention, netnode do have mac address for 10.5.5.5
> If you tcpdump on 10.5.5.5 while pinging from 10.5.5.1, you should
> see ICMP request coming from 10.5.5.1 (provided the 'controller'
> node is the network node)
> Could you also check ARP cache on 10.5.5.5, especially look at
> 10.5.5.1 entry ?
>
> -Sylvain
>
>
> Le 22/02/2013 01:24, Chathura M. Sarathchandra Magurawalage a écrit :
>> 10.5.5.5 = new fedora vm
>>
>> arp entries for the vms.
>> root at controller:~# arp -n | grep 10.5.5.3
>> 10.5.5.3 (incomplete)
>> tapf71b5b86-5c
>> root at controller:~# arp -n | grep 10.5.5.4
>> 10.5.5.4 (incomplete)
>> tapf71b5b86-5c
>> root at controller:~# arp -n | grep 10.5.5.5
>> 10.5.5.5 ether fa:16:3e:7b:ef:84 C qr-4d088f3a-78
>> 10.5.5.5 (incomplete)
>> tapf71b5b86-5c
>>
>> networknode/controller did not have an arp entry for 10.5.5.1.
>>
>> I tried adding arp entry for the 10.5.5.3 but still it did not work.
>>
>> any ideas?
>>
>> thanks.
>>
>> On 21 February 2013 17:41, Chathura M. Sarathchandra Magurawalage
>> <77.chathura at gmail.com <mailto:77.chathura at gmail.com>> wrote:
>>
>> Thanks Sylvain,
>>
>> root at controller:~# ip a
>> 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state
>> UNKNOWN
>> link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
>> inet 127.0.0.1/8 <http://127.0.0.1/8> scope host lo
>> inet6 ::1/128 scope host
>> valid_lft forever preferred_lft forever
>> 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq
>> state UP qlen 1000
>> link/ether d4:ae:52:bb:aa:20 brd ff:ff:ff:ff:ff:ff
>> inet 10.10.10.1/24 <http://10.10.10.1/24> brd
>> 10.10.10.255 scope global eth0
>> inet6 fe80::d6ae:52ff:febb:aa20/64 scope link
>> valid_lft forever preferred_lft forever
>> 3: eth1: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc
>> mq state DOWN qlen 1000
>> link/ether d4:ae:52:bb:aa:21 brd ff:ff:ff:ff:ff:ff
>> 4: eth0.2 at eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500
>> qdisc noqueue state UP
>> link/ether d4:ae:52:bb:aa:20 brd ff:ff:ff:ff:ff:ff
>> inet 192.168.2.225/24 <http://192.168.2.225/24> brd
>> 192.168.2.255 scope global eth0.2
>> inet6 fe80::d6ae:52ff:febb:aa20/64 scope link
>> valid_lft forever preferred_lft forever
>> 5: br-int: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc
>> noqueue state UNKNOWN
>> link/ether ba:7a:e9:dc:2b:41 brd ff:ff:ff:ff:ff:ff
>> inet6 fe80::b87a:e9ff:fedc:2b41/64 scope link
>> valid_lft forever preferred_lft forever
>> 7: br-ex: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc
>> noqueue state UNKNOWN
>> link/ether 9a:41:c8:8a:9e:49 brd ff:ff:ff:ff:ff:ff
>> inet 192.168.2.225/24 <http://192.168.2.225/24> scope
>> global br-ex
>> 8: tapf71b5b86-5c: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500
>> qdisc noqueue state UNKNOWN
>> link/ether 2a:44:a3:d1:7d:f3 brd ff:ff:ff:ff:ff:ff
>> inet 10.5.5.2/24 <http://10.5.5.2/24> brd 10.5.5.255
>> scope global tapf71b5b86-5c
>> inet6 fe80::2844:a3ff:fed1:7df3/64 scope link
>> valid_lft forever preferred_lft forever
>> 9: qr-4d088f3a-78: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500
>> qdisc noqueue state UNKNOWN
>> link/ether ca:5b:8d:4d:6d:fb brd ff:ff:ff:ff:ff:ff
>> inet 10.5.5.1/24 <http://10.5.5.1/24> brd 10.5.5.255
>> scope global qr-4d088f3a-78
>> inet6 fe80::c85b:8dff:fe4d:6dfb/64 scope link
>> valid_lft forever preferred_lft forever
>> 10: qg-6f8374cb-cb: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu
>> 1500 qdisc noqueue state UNKNOWN
>> link/ether 0e:7f:dd:3a:80:bc brd ff:ff:ff:ff:ff:ff
>> inet 192.168.2.151/24 <http://192.168.2.151/24> brd
>> 192.168.2.255 scope global qg-6f8374cb-cb
>> inet6 fe80::c7f:ddff:fe3a:80bc/64 scope link
>> valid_lft forever preferred_lft forever
>> 36: eth1.2 at eth1: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500
>> qdisc noqueue state LOWERLAYERDOWN
>> link/ether d4:ae:52:bb:aa:21 brd ff:ff:ff:ff:ff:ff
>> 39: br-tun: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN
>> link/ether 26:e2:a9:05:3d:4c brd ff:ff:ff:ff:ff:ff
>>
>>
>> But for some reason the "arp" module is not in the cirros
>> cloud image. Do you suggest any other image to create
>> instances with?, which I can log in without having to ssh in
>> first like the ubuntu cloud image.
>>
>> Thanks.
>>
>> On 21 February 2013 16:17, Sylvain Bauza
>> <sylvain.bauza at digimind.com
>> <mailto:sylvain.bauza at digimind.com>> wrote:
>>
>> Could you please :
>> - 'ip a' on network node
>> - 'arp -n' on VM and check '10.5.5.1'
>> - 'arp -n' on netnode and check '10.5.5.3'
>>
>> Connection in between VM and internal gateway is managed
>> thru ARP resolution.
>> If 'arp -n' is giving no MAC address for 10.5.5.1 on VM,
>> try :
>> 1. get the MAC address for 10.5.5.1 on netnode using 'ip a'
>> 2. get the MAC address for 10.5.5.3 on VM using 'ifconfig'
>> 2. add manually an ARP entry for 10.5.5.1 by issuing
>> 'arp -s 10.5.5.1 <netnode_mac_addr>'
>> 3. (if not present on netnode) add manually ARP entry
>> for 10.5.5.3 using 'arp -s 10.5.5.3 <vm_mac_addr>'
>> and check with ping.
>>
>> If that fixes the bug, you have to investigate why ARP
>> resolution is fine for DHCP server but not for gateway.
>> You should see ARP requests on physical layer with 'ARP,
>> Request who-has 10.5.5.1 tell 10.5.5.3, length 28' and
>> ARP reply as follows 'ARP, Reply 10.5.5.1 is-at
>> <mac_addr>, length 28'
>>
>> -Sylvain
>>
>>
>> Le 21/02/2013 16:29, Chathura M. Sarathchandra
>> Magurawalage a écrit :
>>> So I have got two VMs, they can ping eachother. But they
>>> cannot ping the gateway.
>>>
>>> Just for the record. From my controller/network-node I
>>> can ping the provider router.
>>>
>>> root at controller
>>> :~# quantum router-list
>>> +--------------------------------------+-----------------+--------------------------------------------------------+
>>> | id | name | external_gateway_info |
>>> +--------------------------------------+-----------------+--------------------------------------------------------+
>>> | 1b4b108f-aefa-4548-acc4-d2441038a33f | provider-router
>>> | {"network_id": "26b88521-5d1e-4f40-a4f5-74f8a8136335"} |
>>> +--------------------------------------+-----------------+--------------------------------------------------------+
>>>
>>> [DEFAULT]
>>> # Show debugging output in log (sets DEBUG log level
>>> output)
>>> # debug = True
>>>
>>> # L3 requires that an interface driver be set. Choose
>>> the one that best
>>> # matches your plugin.
>>>
>>> # OVS
>>> interface_driver =
>>> quantum.agent.linux.interface.OVSInterfaceDriver
>>> # LinuxBridge
>>> #interface_driver =
>>> quantum.agent.linux.interface.BridgeInterfaceDriver
>>>
>>> # The Quantum user information for accessing the Quantum
>>> API.
>>> auth_url = http://localhost:35357/v2.0
>>> auth_region = RegionOne
>>> admin_tenant_name = service
>>> admin_user = quantum
>>> admin_password = password
>>>
>>> # Use "sudo quantum-rootwrap /etc/quantum/rootwrap.conf"
>>> to use the real
>>> # root filter facility.
>>> # Change to "sudo" to skip the filtering and just run
>>> the comand directly
>>> root_helper = sudo /usr/bin/quantum-rootwrap
>>> /etc/quantum/rootwrap.conf
>>>
>>> # Allow overlapping IP (Must have kernel build with
>>> CONFIG_NET_NS=y and
>>> # iproute2 package that supports namespaces).
>>> use_namespaces = False
>>>
>>> # If use_namespaces is set as False then the agent can
>>> only configure one router.
>>> # This is done by setting the specific router_id.
>>> router_id = 1b4b108f-aefa-4548-acc4-d2441038a33f
>>>
>>> # Each L3 agent can be associated with at most one
>>> external network. This
>>> # value should be set to the UUID of that external
>>> network. If empty,
>>> # the agent will enforce that only a single external
>>> networks exists and
>>> # use that external network id
>>>
>>> gateway_external_network_id =
>>> 26b88521-5d1e-4f40-a4f5-74f8a8136335
>>>
>>> # Indicates that this L3 agent should also handle
>>> routers that do not have
>>> # an external network gateway configured. This option
>>> should be True only
>>> # for a single agent in a Quantum deployment, and may be
>>> False for all agents
>>> # if all routers must have an external network gateway
>>> # handle_internal_only_routers = True
>>>
>>> # Name of bridge used for external network traffic. This
>>> should be set to
>>> # empty value for the linux bridge
>>> external_network_bridge = br-ex
>>>
>>> # IP address used by Nova metadata server
>>> metadata_ip = 192.168.2.225
>>>
>>> # TCP Port used by Nova metadata server
>>> # metadata_port = 8775
>>>
>>> # The time in seconds between state poll requests
>>> # polling_interval = 3
>>>
>>> root at controller:~# sudo tcpdump -i eth0.2 -nn | grep GRE
>>> tcpdump: verbose output suppressed, use -v or -vv for
>>> full protocol decode
>>> listening on eth0.2, link-type EN10MB (Ethernet),
>>> capture size 65535 bytes
>>> 15:17:58.479140 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 98: IP6
>>> fe80::c85b:8dff:fe4d:6dfb > ff02::1:ff4d:6dfb: HBH
>>> ICMP6, multicast listener reportmax resp delay: 0 addr:
>>> ff02::1:ff4d:6dfb, length 24
>>> 15:17:58.627100 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 98: IP6
>>> fe80::2844:a3ff:fed1:7df3 > ff02::1:ffd1:7df3: HBH
>>> ICMP6, multicast listener reportmax resp delay: 0 addr:
>>> ff02::1:ffd1:7df3, length 24
>>> 15:17:59.382410 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.4 tell 10.5.5.2, length 28
>>> 15:18:00.378904 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.4 tell 10.5.5.2, length 28
>>> 15:18:01.378903 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.4 tell 10.5.5.2, length 28
>>> 15:18:02.385160 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.4 tell 10.5.5.2, length 28
>>> 15:18:03.382894 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.4 tell 10.5.5.2, length 28
>>> 15:18:03.388210 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 372: IP
>>> 10.5.5.2.67 > 10.5.5.4.68: BOOTP/DHCP, Reply, length 318
>>> 15:18:03.388236 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 372: IP
>>> 10.5.5.2.67 > 10.5.5.4.68: BOOTP/DHCP, Reply, length 318
>>> 15:18:03.388246 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 372: IP
>>> 10.5.5.2.67 > 10.5.5.4.68: BOOTP/DHCP, Reply, length 318
>>> 15:18:03.388888 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 372: IP
>>> 10.5.5.2.67 > 10.5.5.4.68: BOOTP/DHCP, Reply, length 318
>>> 15:18:08.403093 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.4 tell 10.5.5.2, length 28
>>> 15:18:09.402916 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.4 tell 10.5.5.2, length 28
>>> 15:18:10.298390 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.3 tell 10.5.5.2, length 28
>>> 15:18:10.402924 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.4 tell 10.5.5.2, length 28
>>> 15:18:11.294904 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.3 tell 10.5.5.2, length 28
>>> 15:18:12.294913 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.3 tell 10.5.5.2, length 28
>>> 15:18:25.312944 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.3 tell 10.5.5.2, length 28
>>> 15:18:26.310912 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.3 tell 10.5.5.2, length 28
>>> 15:18:27.310895 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.3 tell 10.5.5.2, length 28
>>> 15:18:32.319959 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.3 tell 10.5.5.2, length 28
>>> 15:18:33.318897 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.3 tell 10.5.5.2, length 28
>>> 15:18:34.318918 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.3 tell 10.5.5.2, length 28
>>> 15:18:35.322834 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.3 tell 10.5.5.2, length 28
>>> 15:18:36.318925 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.3 tell 10.5.5.2, length 28
>>> 15:18:36.325485 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 372: IP
>>> 10.5.5.2.67 > 10.5.5.3.68: BOOTP/DHCP, Reply, length 318
>>> 15:18:36.325511 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 372: IP
>>> 10.5.5.2.67 > 10.5.5.3.68: BOOTP/DHCP, Reply, length 318
>>> 15:18:36.325525 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 372: IP
>>> 10.5.5.2.67 > 10.5.5.3.68: BOOTP/DHCP, Reply, length 318
>>> 15:18:36.326108 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 372: IP
>>> 10.5.5.2.67 > 10.5.5.3.68: BOOTP/DHCP, Reply, length 318
>>> 15:18:41.331088 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.3 tell 10.5.5.2, length 28
>>> 15:18:42.330900 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.3 tell 10.5.5.2, length 28
>>> 15:18:43.330903 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.3 tell 10.5.5.2, length 28
>>> 15:19:03.453248 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.4 tell 10.5.5.2, length 28
>>> 15:19:04.450896 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.4 tell 10.5.5.2, length 28
>>> 15:19:05.450899 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.4 tell 10.5.5.2, length 28
>>> 15:19:33.483521 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.4 tell 10.5.5.2, length 28
>>> 15:19:34.482921 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.4 tell 10.5.5.2, length 28
>>> 15:19:35.482911 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.4 tell 10.5.5.2, length 28
>>> 15:19:36.390216 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.3 tell 10.5.5.2, length 28
>>> 15:19:37.386903 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.3 tell 10.5.5.2, length 28
>>> 15:19:38.386905 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.3 tell 10.5.5.2, length 28
>>> 15:19:48.498690 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.4 tell 10.5.5.2, length 28
>>> 15:19:49.494912 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.4 tell 10.5.5.2, length 28
>>> 15:19:50.494922 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.4 tell 10.5.5.2, length 28
>>> 15:19:55.505851 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.4 tell 10.5.5.2, length 28
>>> 15:19:56.502912 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.4 tell 10.5.5.2, length 28
>>> 15:19:57.502911 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.4 tell 10.5.5.2, length 28
>>> 15:19:58.508429 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.4 tell 10.5.5.2, length 28
>>> 15:19:59.506909 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.4 tell 10.5.5.2, length 28
>>> 15:19:59.511616 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 372: IP
>>> 10.5.5.2.67 > 10.5.5.4.68: BOOTP/DHCP, Reply, length 318
>>> 15:19:59.511641 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 372: IP
>>> 10.5.5.2.67 > 10.5.5.4.68: BOOTP/DHCP, Reply, length 318
>>> 15:19:59.511652 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 372: IP
>>> 10.5.5.2.67 > 10.5.5.4.68: BOOTP/DHCP, Reply, length 318
>>> 15:19:59.512382 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 372: IP
>>> 10.5.5.2.67 > 10.5.5.4.68: BOOTP/DHCP, Reply, length 318
>>> 15:20:03.711078 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 98: IP6
>>> fe80::c85b:8dff:fe4d:6dfb > ff02::1:ff4d:6dfb: HBH
>>> ICMP6, multicast listener reportmax resp delay: 0 addr:
>>> ff02::1:ff4d:6dfb, length 24
>>> 15:20:03.815067 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 98: IP6
>>> fe80::2844:a3ff:fed1:7df3 > ff02::1:ffd1:7df3: HBH
>>> ICMP6, multicast listener reportmax resp delay: 0 addr:
>>> ff02::1:ffd1:7df3, length 24
>>> 15:20:04.515054 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.4 tell 10.5.5.2, length 28
>>> 15:20:05.514893 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.4 tell 10.5.5.2, length 28
>>> 15:20:06.402892 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.3 tell 10.5.5.2, length 28
>>> 15:20:06.514919 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.4 tell 10.5.5.2, length 28
>>> 15:20:07.398910 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.3 tell 10.5.5.2, length 28
>>> 15:20:08.398913 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.3 tell 10.5.5.2, length 28
>>> 15:20:21.404862 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.3 tell 10.5.5.2, length 28
>>> 15:20:22.402900 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.3 tell 10.5.5.2, length 28
>>> 15:20:23.402904 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.3 tell 10.5.5.2, length 28
>>> 15:20:28.405674 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.3 tell 10.5.5.2, length 28
>>> 15:20:29.402894 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.3 tell 10.5.5.2, length 28
>>> 15:20:30.402913 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.3 tell 10.5.5.2, length 28
>>> 15:20:31.405714 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.3 tell 10.5.5.2, length 28
>>> 15:20:32.402919 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.3 tell 10.5.5.2, length 28
>>> 15:20:32.407948 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 372: IP
>>> 10.5.5.2.67 > 10.5.5.3.68: BOOTP/DHCP, Reply, length 318
>>> 15:20:32.407974 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 372: IP
>>> 10.5.5.2.67 > 10.5.5.3.68: BOOTP/DHCP, Reply, length 318
>>> 15:20:32.407986 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 372: IP
>>> 10.5.5.2.67 > 10.5.5.3.68: BOOTP/DHCP, Reply, length 318
>>> 15:20:32.408728 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 372: IP
>>> 10.5.5.2.67 > 10.5.5.3.68: BOOTP/DHCP, Reply, length 318
>>> 15:20:37.411052 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.3 tell 10.5.5.2, length 28
>>> 15:20:38.410918 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.3 tell 10.5.5.2, length 28
>>> 15:20:39.410896 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.3 tell 10.5.5.2, length 28
>>> 15:20:59.567749 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.4 tell 10.5.5.2, length 28
>>> 15:21:00.566914 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.4 tell 10.5.5.2, length 28
>>> 15:21:01.566893 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.4 tell 10.5.5.2, length 28
>>> 15:21:20.539385 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP, Reply
>>> 10.5.5.1 is-at 2a:44:a3:d1:7d:f3, length 28
>>> 15:21:20.539417 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP, Reply
>>> 10.5.5.1 is-at ca:5b:8d:4d:6d:fb, length 28
>>> 15:21:29.583747 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 372: IP
>>> 10.5.5.2.67 > 10.5.5.4.68: BOOTP/DHCP, Reply, length 318
>>> 15:21:29.587195 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP, Reply
>>> 10.5.5.2 is-at 2a:44:a3:d1:7d:f3, length 28
>>> 15:21:29.587220 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP, Reply
>>> 10.5.5.2 is-at ca:5b:8d:4d:6d:fb, length 28
>>> 15:21:32.472558 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.3 tell 10.5.5.2, length 28
>>> 15:21:33.470921 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.3 tell 10.5.5.2, length 28
>>> 15:21:34.470920 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.3 tell 10.5.5.2, length 28
>>> 15:22:02.502741 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.3 tell 10.5.5.2, length 28
>>> 15:22:03.498903 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.3 tell 10.5.5.2, length 28
>>> 15:22:04.498910 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.3 tell 10.5.5.2, length 28
>>> 15:22:07.367450 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP, Reply
>>> 10.5.5.1 is-at 2a:44:a3:d1:7d:f3, length 28
>>> 15:22:07.367476 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP, Reply
>>> 10.5.5.1 is-at ca:5b:8d:4d:6d:fb, length 28
>>> 15:22:08.819063 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 98: IP6
>>> fe80::c85b:8dff:fe4d:6dfb > ff02::1:ff4d:6dfb: HBH
>>> ICMP6, multicast listener reportmax resp delay: 0 addr:
>>> ff02::1:ff4d:6dfb, length 24
>>> 15:22:09.335068 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 98: IP6
>>> fe80::2844:a3ff:fed1:7df3 > ff02::1:ffd1:7df3: HBH
>>> ICMP6, multicast listener reportmax resp delay: 0 addr:
>>> ff02::1:ffd1:7df3, length 24
>>> 15:22:17.517928 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.3 tell 10.5.5.2, length 28
>>> 15:22:18.514903 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.3 tell 10.5.5.2, length 28
>>> 15:22:19.514909 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.3 tell 10.5.5.2, length 28
>>> 15:22:24.525010 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.3 tell 10.5.5.2, length 28
>>> 15:22:25.522896 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.3 tell 10.5.5.2, length 28
>>> 15:22:26.522895 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.3 tell 10.5.5.2, length 28
>>> 15:22:27.527868 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.3 tell 10.5.5.2, length 28
>>> 15:22:28.526907 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.3 tell 10.5.5.2, length 28
>>> 15:22:28.530086 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 372: IP
>>> 10.5.5.2.67 > 10.5.5.3.68: BOOTP/DHCP, Reply, length 318
>>> 15:22:28.530112 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 372: IP
>>> 10.5.5.2.67 > 10.5.5.3.68: BOOTP/DHCP, Reply, length 318
>>> 15:22:28.530122 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 372: IP
>>> 10.5.5.2.67 > 10.5.5.3.68: BOOTP/DHCP, Reply, length 318
>>> 15:22:28.530578 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 372: IP
>>> 10.5.5.2.67 > 10.5.5.3.68: BOOTP/DHCP, Reply, length 318
>>> 15:22:29.591728 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 372: IP
>>> 10.5.5.2.67 > 10.5.5.4.68: BOOTP/DHCP, Reply, length 318
>>> 15:22:33.539073 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.3 tell 10.5.5.2, length 28
>>> 15:22:34.538891 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.3 tell 10.5.5.2, length 28
>>> 15:22:34.595074 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.4 tell 10.5.5.2, length 28
>>> 15:22:35.538887 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.3 tell 10.5.5.2, length 28
>>> 15:22:35.594887 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.4 tell 10.5.5.2, length 28
>>> 15:22:36.594890 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.4 tell 10.5.5.2, length 28
>>> 15:22:45.371464 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP, Reply
>>> 10.5.5.1 is-at 2a:44:a3:d1:7d:f3, length 28
>>> 15:22:45.371493 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP, Reply
>>> 10.5.5.1 is-at ca:5b:8d:4d:6d:fb, length 28
>>> icmpicmpicmpicmpicmpicmp15:23:23.375417 IP 192.168.2.225
>>> > 10.0.0.3 <http://10.0.0.3>: GREv0, key=0x1, length 54:
>>> ARP, Reply 10.5.5.1 is-at 2a:44:a3:d1:7d:f3, length 28
>>> 15:23:23.375446 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP, Reply
>>> 10.5.5.1 is-at ca:5b:8d:4d:6d:fb, length 28
>>> uest who-has 10.5.5.4 tell 10.5.5.2, length 28
>>> 15:18:09.402916 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.4 tell 10.5.5.2, length 28
>>> 15:18:10.298390 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.3 tell 10.5.5.2, length 28
>>> 15:18:10.402924 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.4 tell 10.5.5.2, length 28
>>> 15:18:11.294904 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.3 tell 10.5.5.2, length 28
>>> 15:18:12.294913 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.3 tell 10.5.5.2, length 28
>>> 15:18:25.312944 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.3 tell 10.5.5.2, length 28
>>> 15:18:26.310912 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.3 tell 10.5.5.2, length 28
>>> 15:18:27.310895 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.3 tell 10.5.5.2, length 28
>>> 15:18:32.319959 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.3 tell 10.5.5.2, length 28
>>> 15:18:33.318897 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.3 tell 10.5.5.2, length 28
>>> 15:18:34.318918 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.3 tell 10.5.5.2, length 28
>>> 15:18:35.322834 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.3 tell 10.5.5.2, length 28
>>> 15:18:36.318925 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.3 tell 10.5.5.2, length 28
>>> 15:18:36.325485 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 372: IP
>>> 10.5.5.2.67 > 10.5.5.3.68: BOOTP/DHCP, Reply, length 318
>>> 15:18:36.325511 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 372: IP
>>> 10.5.5.2.67 > 10.5.5.3.68: BOOTP/DHCP, Reply, length 318
>>> 15:18:36.325525 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 372: IP
>>> 10.5.5.2.67 > 10.5.5.3.68: BOOTP/DHCP, Reply, length 318
>>> 15:18:36.326108 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 372: IP
>>> 10.5.5.2.67 > 10.5.5.3.68: BOOTP/DHCP, Reply, length 318
>>> 15:18:41.331088 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.3 tell 10.5.5.2, length 28
>>> 15:18:42.330900 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.3 tell 10.5.5.2, length 28
>>> 15:18:43.330903 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.3 tell 10.5.5.2, length 28
>>> 15:19:03.453248 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.4 tell 10.5.5.2, length 28
>>> 15:19:04.450896 IP 192.168.2.225 > 10.0.0.3
>>> <http://10.0.0.3>: GREv0, key=0x1, length 54: ARP,
>>> Request who-has 10.5.5.4 tell 10.5.5.2, length 28
>>> ......
>>>
>>> Thanks.
>>>
>>> On 21 February 2013 12:45, Sylvain Bauza
>>> <sylvain.bauza at digimind.com
>>> <mailto:sylvain.bauza at digimind.com>> wrote:
>>>
>>> Thanks for the heads-up. So, the VM is able to reach
>>> the DHCP server and get a lease, but unable to
>>> contact the provider router IP (on its subnet).
>>> Could you please start a second VM using the same
>>> way and check network connectivity in between both ?
>>>
>>> I would say the issue is tied to the L3 agent, as
>>> DHCP is working and communication is OK.
>>> Please check on the physical layer (probably eth0)
>>> on network node that GRE'd ICMP packet is coming in
>>> (and hoping coming *back*) when pinging your gateway :
>>>
>>> sudo tcpdump -i eth0 -nn | grep GRE
>>>
>>>
>>> Also, make sure /etc/quantum/l3_agent.ini is correct
>>> with router_id and gateway_external_net_id set
>>> correctly.
>>>
>>> -Sylvain
>>>
>>> Le 21/02/2013 12:45, Chathura M. Sarathchandra
>>> Magurawalage a écrit :
>>>> Hello
>>>>
>>>> Sorry, it comes to the log in prompt but it takes
>>>> quite long, I just did not realise.
>>>>
>>>> I have got a running Corros VM. This is the log.
>>>>
>>>> [ 0.000000] Initializing cgroup subsys cpuset
>>>> [ 0.000000] Initializing cgroup subsys cpu
>>>> [ 0.000000] Linux version 3.0.0-12-virtual (buildd at crested) (gcc version 4.6.1 (Ubuntu/Linaro 4.6.1-9ubuntu3) ) #20-Ubuntu SMP Fri Oct 7 18:19:02 UTC 2011 (Ubuntu 3.0.0-12.20-virtual 3.0.4)
>>>> [ 0.000000] Command line: LABEL=cirros-rootfs ro console=tty0 console=ttyS0 console=hvc0
>>>> [ 0.000000] KERNEL supported cpus:
>>>> [ 0.000000] Intel GenuineIntel
>>>> [ 0.000000] AMD AuthenticAMD
>>>> [ 0.000000] Centaur CentaurHauls
>>>> [ 0.000000] BIOS-provided physical RAM map:
>>>> [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009dc00 (usable)
>>>> [ 0.000000] BIOS-e820: 000000000009dc00 - 00000000000a0000 (reserved)
>>>> [ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
>>>> [ 0.000000] BIOS-e820: 0000000000100000 - 000000001fffd000 (usable)
>>>> [ 0.000000] BIOS-e820: 000000001fffd000 - 0000000020000000 (reserved)
>>>> [ 0.000000] BIOS-e820: 00000000feffc000 - 00000000ff000000 (reserved)
>>>> [ 0.000000] BIOS-e820: 00000000fffc0000 - 0000000100000000 (reserved)
>>>> [ 0.000000] NX (Execute Disable) protection: active
>>>> [ 0.000000] DMI 2.4 present.
>>>> [ 0.000000] No AGP bridge found
>>>> [ 0.000000] last_pfn = 0x1fffd max_arch_pfn = 0x400000000
>>>> [ 0.000000] x86 PAT enabled: cpu 0, old 0x70406, new 0x7010600070106
>>>> [ 0.000000] found SMP MP-table at [ffff8800000fdaf0] fdaf0
>>>> [ 0.000000] init_memory_mapping: 0000000000000000-000000001fffd000
>>>> [ 0.000000] RAMDISK: 1fdf9000 - 1ffed000
>>>> [ 0.000000] ACPI: RSDP 00000000000fd990 00014 (v00 BOCHS )
>>>> [ 0.000000] ACPI: RSDT 000000001fffd7b0 00034 (v01 BOCHS BXPCRSDT 00000001 BXPC 00000001)
>>>> [ 0.000000] ACPI: FACP 000000001fffff80 00074 (v01 BOCHS BXPCFACP 00000001 BXPC 00000001)
>>>> [ 0.000000] ACPI: DSDT 000000001fffd9b0 02589 (v01 BXPC BXDSDT 00000001 INTL 20100528)
>>>> [ 0.000000] ACPI: FACS 000000001fffff40 00040
>>>> [ 0.000000] ACPI: SSDT 000000001fffd910 0009E (v01 BOCHS BXPCSSDT 00000001 BXPC 00000001)
>>>> [ 0.000000] ACPI: APIC 000000001fffd830 00072 (v01 BOCHS BXPCAPIC 00000001 BXPC 00000001)
>>>> [ 0.000000] ACPI: HPET 000000001fffd7f0 00038 (v01 BOCHS BXPCHPET 00000001 BXPC 00000001)
>>>> [ 0.000000] No NUMA configuration found
>>>> [ 0.000000] Faking a node at 0000000000000000-000000001fffd000
>>>> [ 0.000000] Initmem setup node 0 0000000000000000-000000001fffd000
>>>> [ 0.000000] NODE_DATA [000000001fff5000 - 000000001fff9fff]
>>>> [ 0.000000] kvm-clock: Using msrs 4b564d01 and 4b564d00
>>>> [ 0.000000] kvm-clock: cpu 0, msr 0:1ce28c1, boot clock
>>>> [ 0.000000] Zone PFN ranges:
>>>> [ 0.000000] DMA 0x00000010 -> 0x00001000
>>>> [ 0.000000] DMA32 0x00001000 -> 0x00100000
>>>> [ 0.000000] Normal empty
>>>> [ 0.000000] Movable zone start PFN for each node
>>>> [ 0.000000] early_node_map[2] active PFN ranges
>>>> [ 0.000000] 0: 0x00000010 -> 0x0000009d
>>>> [ 0.000000] 0: 0x00000100 -> 0x0001fffd
>>>> [ 0.000000] ACPI: PM-Timer IO Port: 0xb008
>>>> [ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
>>>> [ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
>>>> [ 0.000000] IOAPIC[0]: apic_id 1, version 17, address 0xfec00000, GSI 0-23
>>>> [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
>>>> [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 5 global_irq 5 high level)
>>>> [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
>>>> [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 10 global_irq 10 high level)
>>>> [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 11 global_irq 11 high level)
>>>> [ 0.000000] Using ACPI (MADT) for SMP configuration information
>>>> [ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
>>>> [ 0.000000] SMP: Allowing 1 CPUs, 0 hotplug CPUs
>>>> [ 0.000000] PM: Registered nosave memory: 000000000009d000 - 000000000009e000
>>>> [ 0.000000] PM: Registered nosave memory: 000000000009e000 - 00000000000a0000
>>>> [ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
>>>> [ 0.000000] PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
>>>> [ 0.000000] Allocating PCI resources starting at 20000000 (gap: 20000000:deffc000)
>>>> [ 0.000000] Booting paravirtualized kernel on KVM
>>>> [ 0.000000] setup_percpu: NR_CPUS:64 nr_cpumask_bits:64 nr_cpu_ids:1 nr_node_ids:1
>>>> [ 0.000000] PERCPU: Embedded 27 pages/cpu @ffff88001fa00000 s79296 r8192 d23104 u2097152
>>>> [ 0.000000] kvm-clock: cpu 0, msr 0:1fa128c1, primary cpu clock
>>>> [ 0.000000] KVM setup async PF for cpu 0
>>>> [ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 129157
>>>> [ 0.000000] Policy zone: DMA32
>>>> [ 0.000000] Kernel command line: LABEL=cirros-rootfs ro console=tty0 console=ttyS0 console=hvc0
>>>> [ 0.000000] PID hash table entries: 2048 (order: 2, 16384 bytes)
>>>> [ 0.000000] xsave/xrstor: enabled xstate_bv 0x7, cntxt size 0x340
>>>> [ 0.000000] Checking aperture...
>>>> [ 0.000000] No AGP bridge found
>>>> [ 0.000000] Memory: 497852k/524276k available (6206k kernel code, 460k absent, 25964k reserved, 6907k data, 900k init)
>>>> [ 0.000000] SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
>>>> [ 0.000000] Hierarchical RCU implementation.
>>>> [ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
>>>> [ 0.000000] NR_IRQS:4352 nr_irqs:256 16
>>>> [ 0.000000] Console: colour VGA+ 80x25
>>>> [ 0.000000] console [tty0] enabled
>>>> [ 0.000000] console [ttyS0] enabled
>>>> [ 0.000000] allocated 4194304 bytes of page_cgroup
>>>> [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
>>>> [ 0.000000] Detected 3392.282 MHz processor.
>>>> [ 0.008000] Calibrating delay loop (skipped) preset value.. 6784.56 BogoMIPS (lpj=13569128)
>>>> [ 0.008000] pid_max: default: 32768 minimum: 301
>>>> [ 0.008000] Security Framework initialized
>>>> [ 0.008000] AppArmor: AppArmor initialized
>>>> [ 0.008000] Yama: becoming mindful.
>>>> [ 0.008000] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
>>>> [ 0.008292] Inode-cache hash table entries: 32768 (order: 6, 262144 bytes)
>>>> [ 0.009146] Mount-cache hash table entries: 256
>>>> [ 0.009772] Initializing cgroup subsys cpuacct
>>>> [ 0.010285] Initializing cgroup subsys memory
>>>> [ 0.010791] Initializing cgroup subsys devices
>>>> [ 0.011312] Initializing cgroup subsys freezer
>>>> [ 0.012004] Initializing cgroup subsys net_cls
>>>> [ 0.012523] Initializing cgroup subsys blkio
>>>> [ 0.013027] Initializing cgroup subsys perf_event
>>>> [ 0.013608] mce: CPU supports 10 MCE banks
>>>> [ 0.014264] SMP alternatives: switching to UP code
>>>> [ 0.028279] Freeing SMP alternatives: 24k freed
>>>> [ 0.028805] ACPI: Core revision 20110413
>>>> [ 0.029869] ftrace: allocating 26075 entries in 103 pages
>>>> [ 0.032199] Enabling x2apic
>>>> [ 0.032576] Enabled x2apic
>>>> [ 0.036005] Switched APIC routing to physical x2apic.
>>>> [ 0.037122] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
>>>> [ 0.037755] CPU0: Intel(R) Xeon(R) CPU E3-1240 V2 @ 3.40GHz stepping 09
>>>> [ 0.040002] Performance Events: unsupported p6 CPU model 58 no PMU driver, software events only.
>>>> [ 0.040002] Brought up 1 CPUs
>>>> [ 0.040002] Total of 1 processors activated (6784.56 BogoMIPS).
>>>> [ 0.040002] devtmpfs: initialized
>>>> [ 0.040252] print_constraints: dummy:
>>>> [ 0.040734] Time: 12:52:56 Date: 02/20/13
>>>> [ 0.041230] NET: Registered protocol family 16
>>>> [ 0.041798] ACPI: bus type pci registered
>>>> [ 0.042317] PCI: Using configuration type 1 for base access
>>>> [ 0.043298] bio: create slab <bio-0> at 0
>>>> [ 0.044935] ACPI: Interpreter enabled
>>>> [ 0.045378] ACPI: (supports S0 S3 S4 S5)
>>>> [ 0.046026] ACPI: Using IOAPIC for interrupt routing
>>>> [ 0.048451] ACPI: No dock devices found.
>>>> [ 0.048911] HEST: Table not found.
>>>> [ 0.049321] PCI: Ignoring host bridge windows from ACPI; if necessary, use "pci=use_crs" and report a bug
>>>> [ 0.050338] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
>>>> [ 0.052351] pci 0000:00:01.3: quirk: [io 0xb000-0xb03f] claimed by PIIX4 ACPI
>>>> [ 0.053173] pci 0000:00:01.3: quirk: [io 0xb100-0xb10f] claimed by PIIX4 SMB
>>>> [ 0.068180] pci0000:00: Unable to request _OSC control (_OSC support mask: 0x1e)
>>>> [ 0.072782] ACPI: PCI Interrupt Link [LNKA] (IRQs 5 *10 11)
>>>> [ 0.073647] ACPI: PCI Interrupt Link [LNKB] (IRQs 5 *10 11)
>>>> [ 0.074501] ACPI: PCI Interrupt Link [LNKC] (IRQs 5 10 *11)
>>>> [ 0.075362] ACPI: PCI Interrupt Link [LNKD] (IRQs 5 10 *11)
>>>> [ 0.076190] ACPI: PCI Interrupt Link [LNKS] (IRQs 9) *0
>>>> [ 0.077090] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
>>>> [ 0.077982] vgaarb: loaded
>>>> [ 0.078336] vgaarb: bridge control possible 0000:00:02.0
>>>> [ 0.079070] SCSI subsystem initialized
>>>> [ 0.079669] usbcore: registered new interface driver usbfs
>>>> [ 0.080016] usbcore: registered new interface driver hub
>>>> [ 0.080613] usbcore: registered new device driver usb
>>>> [ 0.081265] PCI: Using ACPI for IRQ routing
>>>> [ 0.081952] NetLabel: Initializing
>>>> [ 0.082368] NetLabel: domain hash size = 128
>>>> [ 0.082869] NetLabel: protocols = UNLABELED CIPSOv4
>>>> [ 0.083417] NetLabel: unlabeled traffic allowed by default
>>>> [ 0.084051] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
>>>> [ 0.084774] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
>>>> [ 0.085480] hpet0: 3 comparators, 64-bit 100.000000 MHz counter
>>>> [ 0.092086] Switching to clocksource kvm-clock
>>>> [ 0.095414] Switched to NOHz mode on CPU #0
>>>> [ 0.097611] AppArmor: AppArmor Filesystem Enabled
>>>> [ 0.098148] pnp: PnP ACPI init
>>>> [ 0.098557] ACPI: bus type pnp registered
>>>> [ 0.099474] pnp: PnP ACPI: found 8 devices
>>>> [ 0.099943] ACPI: ACPI bus type pnp unregistered
>>>> [ 0.105880] NET: Registered protocol family 2
>>>> [ 0.106424] IP route cache hash table entries: 4096 (order: 3, 32768 bytes)
>>>> [ 0.107293] TCP established hash table entries: 16384 (order: 6, 262144 bytes)
>>>> [ 0.108257] TCP bind hash table entries: 16384 (order: 6, 262144 bytes)
>>>> [ 0.109056] TCP: Hash tables configured (established 16384 bind 16384)
>>>> [ 0.109725] TCP reno registered
>>>> [ 0.110113] UDP hash table entries: 256 (order: 1, 8192 bytes)
>>>> [ 0.110736] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
>>>> [ 0.111434] NET: Registered protocol family 1
>>>> [ 0.111938] pci 0000:00:00.0: Limiting direct PCI/PCI transfers
>>>> [ 0.112577] pci 0000:00:01.0: PIIX3: Enabling Passive Release
>>>> [ 0.113189] pci 0000:00:01.0: Activating ISA DMA hang workarounds
>>>> [ 0.114074] Trying to unpack rootfs image as initramfs...
>>>> [ 0.120216] audit: initializing netlink socket (disabled)
>>>> [ 0.120809] type=2000 audit(1361364777.116:1): initialized
>>>> [ 0.150148] HugeTLB registered 2 MB page size, pre-allocated 0 pages
>>>> [ 0.156115] VFS: Disk quotas dquot_6.5.2
>>>> [ 0.156620] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
>>>> [ 0.157660] fuse init (API version 7.16)
>>>> [ 0.158180] msgmni has been set to 972
>>>> [ 0.161560] Freeing initrd memory: 2000k freed
>>>> [ 0.165512] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
>>>> [ 0.166371] io scheduler noop registered
>>>> [ 0.166837] io scheduler deadline registered (default)
>>>> [ 0.167423] io scheduler cfq registered
>>>> [ 0.167937] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
>>>> [ 0.168560] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
>>>> [ 0.169312] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
>>>> [ 0.170146] ACPI: Power Button [PWRF]
>>>> [ 0.171093] ERST: Table is not found!
>>>> [ 0.171635] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
>>>> [ 0.172268] virtio-pci 0000:00:03.0: PCI INT A -> Link[LNKC] -> GSI 11 (level, high) -> IRQ 11
>>>> [ 0.173342] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 10
>>>> [ 0.173965] virtio-pci 0000:00:04.0: PCI INT A -> Link[LNKD] -> GSI 10 (level, high) -> IRQ 10
>>>> [ 0.175396] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 10
>>>> [ 0.176908] virtio-pci 0000:00:05.0: PCI INT A -> Link[LNKA] -> GSI 10 (level, high) -> IRQ 10
>>>> [ 0.179328] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
>>>> [ 0.202858] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
>>>> [ 0.223658] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
>>>> [ 0.245496] 00:05: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
>>>> [ 0.266837] 00:06: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
>>>> [ 0.267546] Linux agpgart interface v0.103
>>>> [ 0.268626] brd: module loaded
>>>> [ 0.269293] loop: module loaded
>>>> [ 0.283115] vda: vda1
>>>> [ 0.285258] scsi0 : ata_piix
>>>> [ 0.286262] scsi1 : ata_piix
>>>> [ 0.287206] ata1: PATA max MWDMA2 cmd 0x1f0 ctl 0x3f6 bmdma 0xc0a0 irq 14
>>>> [ 0.288840] ata2: PATA max MWDMA2 cmd 0x170 ctl 0x376 bmdma 0xc0a8 irq 15
>>>> [ 0.290751] Fixed MDIO Bus: probed
>>>> [ 0.291758] PPP generic driver version 2.4.2
>>>> [ 0.292961] tun: Universal TUN/TAP device driver, 1.6
>>>> [ 0.294237] tun: (C) 1999-2004 Max Krasnyansky <maxk at qualcomm.com <mailto:maxk at qualcomm.com>>
>>>> [ 0.367427] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
>>>> [ 0.369053] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
>>>> [ 0.370623] uhci_hcd: USB Universal Host Controller Interface driver
>>>> [ 0.372247] uhci_hcd 0000:00:01.2: PCI INT D -> Link[LNKD] -> GSI 10 (level, high) -> IRQ 10
>>>> [ 0.374444] uhci_hcd 0000:00:01.2: UHCI Host Controller
>>>> [ 0.375886] uhci_hcd 0000:00:01.2: new USB bus registered, assigned bus number 1
>>>> [ 0.378008] uhci_hcd 0000:00:01.2: irq 10, io base 0x0000c040
>>>> [ 0.379709] hub 1-0:1.0: USB hub found
>>>> [ 0.380843] hub 1-0:1.0: 2 ports detected
>>>> [ 0.382181] i8042: PNP: PS/2 Controller [PNP0303:KBD,PNP0f13:MOU] at 0x60,0x64 irq 1,12
>>>> [ 0.383712] serio: i8042 KBD port at 0x60,0x64 irq 1
>>>> [ 0.384268] serio: i8042 AUX port at 0x60,0x64 irq 12
>>>> [ 0.384902] mousedev: PS/2 mouse device common for all mice
>>>> [ 0.385581] rtc_cmos 00:01: RTC can wake from S4
>>>> [ 0.386219] rtc_cmos 00:01: rtc core: registered rtc_cmos as rtc0
>>>> [ 0.386944] rtc0: alarms up to one day, 114 bytes nvram, hpet irqs
>>>> [ 0.387677] device-mapper: uevent: version 1.0.3
>>>> [ 0.388249] device-mapper: ioctl: 4.20.0-ioctl (2011-02-02) initialised:dm-devel at redhat.com <mailto:dm-devel at redhat.com>
>>>> [ 0.389200] cpuidle: using governor ladder
>>>> [ 0.389694] cpuidle: using governor menu
>>>> [ 0.390148] EFI Variables Facility v0.08 2004-May-17
>>>> [ 0.390826] TCP cubic registered
>>>> [ 0.391311] NET: Registered protocol family 10
>>>> [ 0.392174] NET: Registered protocol family 17
>>>> [ 0.392714] Registering the dns_resolver key type
>>>> [ 0.393321] registered taskstats version 1
>>>> [ 0.393981] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
>>>> [ 0.397108] Magic number: 1:90:886
>>>> [ 0.397602] rtc_cmos 00:01: setting system clock to 2013-02-20 12:52:56 UTC (1361364776)
>>>> [ 0.398525] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
>>>> [ 0.399188] EDD information not available.
>>>> [ 0.550030] Freeing unused kernel memory: 900k freed
>>>> [ 0.551849] Write protecting the kernel read-only data: 12288k
>>>> [ 0.560335] Freeing unused kernel memory: 1968k freed
>>>> [ 0.564771] Freeing unused kernel memory: 1368k freed
>>>>
>>>> info: initramfs: up at 0.56
>>>> NOCHANGE: partition 1 is size 64260. it cannot be grown
>>>> info: initramfs loading root from /dev/vda1
>>>> info: /etc/init.d/rc.sysinit: up at 0.72
>>>> [ 0.722727] EXT3-fs (vda1): warning: checktime reached, running e2fsck is recommended
>>>> Starting logging: OK
>>>> Initializing random number generator... done.
>>>> Starting network...
>>>> udhcpc (v1.18.5) started
>>>> Sending discover...
>>>> Sending select for 10.5.5.3...
>>>> Lease of 10.5.5.3 obtained, lease time 120
>>>> deleting routers
>>>> route: SIOCDELRT: No such process
>>>> adding dns 8.8.8.8
>>>> cloud-setup: checkinghttp://169.254.169.254/2009-04-04/meta-data/instance-id
>>>> wget: can't connect to remote host (169.254.169.254): Connection timed out
>>>> cloud-setup: failed 1/30: up 0.84. request failed
>>>> wget: can't connect to remote host (169.254.169.254): Connection timed out
>>>> cloud-setup: failed 2/30: up 191.17. request failed
>>>> wget: can't connect to remote host (169.254.169.254): Connection timed out
>>>> cloud-setup: failed 3/30: up 381.64. request failed
>>>> wget: can't connect to remote host (169.254.169.254): Connection timed out
>>>> cloud-setup: failed 4/30: up 572.10. request failed
>>>> wget: can't connect to remote host (169.254.169.254): Connection timed out
>>>> cloud-setup: failed 5/30: up 762.57. request failed
>>>> wget: can't connect to remote host (169.254.169.254): Connection timed out
>>>> cloud-setup: failed 6/30: up 953.03. request failed
>>>> wget: can't connect to remote host (169.254.169.254): Connection timed out
>>>> cloud-setup: failed 7/30: up 1143.49. request failed
>>>> wget: can't connect to remote host (169.254.169.254): Connection timed out
>>>> cloud-setup: failed 8/30: up 1333.96. request failed
>>>> wget: can't connect to remote host (169.254.169.254): Connection timed out
>>>> cloud-setup: failed 9/30: up 1524.42. request failed
>>>> wget: can't connect to remote host (169.254.169.254): Connection timed out
>>>> cloud-setup: failed 10/30: up 1714.89. request failed
>>>> wget: can't connect to remote host (169.254.169.254): Connection timed out
>>>> cloud-setup: failed 11/30: up 1905.35. request failed
>>>> wget: can't connect to remote host (169.254.169.254): Connection timed out
>>>> cloud-setup: failed 12/30: up 2095.81. request failed
>>>> wget: can't connect to remote host (169.254.169.254): Connection timed out
>>>> cloud-setup: failed 13/30: up 2286.28. request failed
>>>> wget: can't connect to remote host (169.254.169.254): Connection timed out
>>>> cloud-setup: failed 14/30: up 2476.74. request failed
>>>> wget: can't connect to remote host (169.254.169.254): Connection timed out
>>>> cloud-setup: failed 15/30: up 2667.21. request failed
>>>> wget: can't connect to remote host (169.254.169.254): Connection timed out
>>>> cloud-setup: failed 16/30: up 2857.67. request failed
>>>> wget: can't connect to remote host (169.254.169.254): Connection timed out
>>>> cloud-setup: failed 17/30: up 3048.13. request failed
>>>> wget: can't connect to remote host (169.254.169.254): Connection timed out
>>>> cloud-setup: failed 18/30: up 3238.60. request failed
>>>> wget: can't connect to remote host (169.254.169.254): Connection timed out
>>>> cloud-setup: failed 19/30: up 3429.06. request failed
>>>> wget: can't connect to remote host (169.254.169.254): Connection timed out
>>>> cloud-setup: failed 20/30: up 3619.53. request failed
>>>> wget: can't connect to remote host (169.254.169.254): Connection timed out
>>>> cloud-setup: failed 21/30: up 3809.99. request failed
>>>> wget: can't connect to remote host (169.254.169.254): Connection timed out
>>>> cloud-setup: failed 22/30: up 4000.45. request failed
>>>> wget: can't connect to remote host (169.254.169.254): Connection timed out
>>>> cloud-setup: failed 23/30: up 4190.92. request failed
>>>> wget: can't connect to remote host (169.254.169.254): Connection timed out
>>>> cloud-setup: failed 24/30: up 4381.38. request failed
>>>> wget: can't connect to remote host (169.254.169.254): Connection timed out
>>>> cloud-setup: failed 25/30: up 4571.85. request failed
>>>> wget: can't connect to remote host (169.254.169.254): Connection timed out
>>>> cloud-setup: failed 26/30: up 4762.31. request failed
>>>> wget: can't connect to remote host (169.254.169.254): Connection timed out
>>>> cloud-setup: failed 27/30: up 4952.77. request failed
>>>> wget: can't connect to remote host (169.254.169.254): Connection timed out
>>>> cloud-setup: failed 28/30: up 5143.24. request failed
>>>> wget: can't connect to remote host (169.254.169.254): Connection timed out
>>>> cloud-setup: failed 29/30: up 5333.70. request failed
>>>> wget: can't connect to remote host (169.254.169.254): Connection timed out
>>>> cloud-setup: failed 30/30: up 5524.17. request failed
>>>> cloud-setup: after 30 fails, debugging
>>>> cloud-setup: running debug (30 tries reached)
>>>> ############ debug start ##############
>>>> ### /etc/rc.d/init.d/sshd start
>>>> /etc/rc3.d/S45-cloud-setup: line 66: /etc/rc.d/init.d/sshd: not found
>>>> ### ifconfig -a
>>>> eth0 Link encap:Ethernet HWaddr FA:16:3E:A2:6E:02
>>>> inet addr:10.5.5.3 Bcast:10.5.5.255 Mask:255.255.255.0
>>>> inet6 addr: fe80::f816:3eff:fea2:6e02/64 Scope:Link
>>>> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
>>>> RX packets:1025 errors:0 dropped:0 overruns:0 frame:0
>>>> TX packets:1190 errors:0 dropped:0 overruns:0 carrier:0
>>>> collisions:0 txqueuelen:1000
>>>> RX bytes:127682 (124.6 KiB) TX bytes:125076 (122.1 KiB)
>>>>
>>>> lo Link encap:Local Loopback
>>>> inet addr:127.0.0.1 Mask:255.0.0.0
>>>> inet6 addr: ::1/128 Scope:Host
>>>> UP LOOPBACK RUNNING MTU:16436 Metric:1
>>>> RX packets:0 errors:0 dropped:0 overruns:0 frame:0
>>>> TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
>>>> collisions:0 txqueuelen:0
>>>> RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
>>>>
>>>> ### route -n
>>>> Kernel IP routing table
>>>> Destination Gateway Genmask Flags Metric Ref Use Iface
>>>> 0.0.0.0 10.5.5.1 0.0.0.0 UG 0 0 0 eth0
>>>> 10.5.5.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0
>>>> ### cat /etc/resolv.conf
>>>> search openstacklocal
>>>> nameserver 8.8.8.8
>>>> ### ping -c 5 10.5.5.1
>>>> PING 10.5.5.1 (10.5.5.1): 56 data bytes
>>>>
>>>> --- 10.5.5.1 ping statistics ---
>>>> 5 packets transmitted, 0 packets received, 100% packet loss
>>>> ### pinging nameservers
>>>> #### ping -c 5 8.8.8.8
>>>> PING 8.8.8.8 (8.8.8.8): 56 data bytes
>>>>
>>>> --- 8.8.8.8 ping statistics ---
>>>> 5 packets transmitted, 0 packets received, 100% packet loss
>>>> ### uname -a
>>>> Linux cirros 3.0.0-12-virtual #20-Ubuntu SMP Fri Oct 7 18:19:02 UTC 2011 x86_64 GNU/Linux
>>>> ### lsmod
>>>> Module Size Used by Not tainted
>>>> vfat 17585 0
>>>> fat 61475 1 vfat
>>>> isofs 40253 0
>>>> ip_tables 27473 0
>>>> x_tables 29846 1 ip_tables
>>>> pcnet32 42078 0
>>>> 8139cp 27412 0
>>>> ne2k_pci 13691 0
>>>> 8390 18856 1 ne2k_pci
>>>> e1000 108573 0
>>>> acpiphp 24080 0
>>>> ### dmesg | tail
>>>> [ 0.763132] acpiphp: Slot [30] registered
>>>> [ 0.763139] acpiphp: Slot [31] registered
>>>> [ 0.767287] e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k8-NAPI
>>>> [ 0.767291] e1000: Copyright (c) 1999-2006 Intel Corporation.
>>>> [ 0.770137] ne2k-pci.c:v1.03 9/22/2003 D. Becker/P. Gortmaker
>>>> [ 0.772344] 8139cp: 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
>>>> [ 0.781780] pcnet32: pcnet32.c:v1.35 21.Apr.2008tsbogend at alpha.franken.de <mailto:tsbogend at alpha.franken.de>
>>>> [ 0.786775] ip_tables: (C) 2000-2006 Netfilter Core Team
>>>> [ 1.112086] Refined TSC clocksource calibration: 3392.132 MHz.
>>>> [ 1.680348] eth0: IPv6 duplicate address fe80::f816:3eff:fea2:6e02 detected!
>>>> ### tail -n 25 /var/log/messages
>>>> Feb 20 05:52:56 cirroskern.info <http://kern.info> kernel: [ 0.763011] acpiphp: Slot [15] registered
>>>> Feb 20 05:52:56 cirroskern.info <http://kern.info> kernel: [ 0.763018] acpiphp: Slot [16] registered
>>>> Feb 20 05:52:56 cirroskern.info <http://kern.info> kernel: [ 0.763025] acpiphp: Slot [17] registered
>>>> Feb 20 05:52:56 cirroskern.info <http://kern.info> kernel: [ 0.763033] acpiphp: Slot [18] registered
>>>> Feb 20 05:52:56 cirroskern.info <http://kern.info> kernel: [ 0.763040] acpiphp: Slot [19] registered
>>>> Feb 20 05:52:56 cirroskern.info <http://kern.info> kernel: [ 0.763047] acpiphp: Slot [20] registered
>>>> Feb 20 05:52:56 cirroskern.info <http://kern.info> kernel: [ 0.763054] acpiphp: Slot [21] registered
>>>> Feb 20 05:52:56 cirroskern.info <http://kern.info> kernel: [ 0.763062] acpiphp: Slot [22] registered
>>>> Feb 20 05:52:56 cirroskern.info <http://kern.info> kernel: [ 0.763070] acpiphp: Slot [23] registered
>>>> Feb 20 05:52:56 cirroskern.info <http://kern.info> kernel: [ 0.763077] acpiphp: Slot [24] registered
>>>> Feb 20 05:52:56 cirroskern.info <http://kern.info> kernel: [ 0.763084] acpiphp: Slot [25] registered
>>>> Feb 20 05:52:56 cirroskern.info <http://kern.info> kernel: [ 0.763091] acpiphp: Slot [26] registered
>>>> Feb 20 05:52:56 cirroskern.info <http://kern.info> kernel: [ 0.763099] acpiphp: Slot [27] registered
>>>> Feb 20 05:52:56 cirroskern.info <http://kern.info> kernel: [ 0.763106] acpiphp: Slot [28] registered
>>>> Feb 20 05:52:56 cirroskern.info <http://kern.info> kernel: [ 0.763124] acpiphp: Slot [29] registered
>>>> Feb 20 05:52:56 cirroskern.info <http://kern.info> kernel: [ 0.763132] acpiphp: Slot [30] registered
>>>> Feb 20 05:52:56 cirroskern.info <http://kern.info> kernel: [ 0.763139] acpiphp: Slot [31] registered
>>>> Feb 20 05:52:56 cirroskern.info <http://kern.info> kernel: [ 0.767287] e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k8-NAPI
>>>> Feb 20 05:52:56 cirroskern.info <http://kern.info> kernel: [ 0.767291] e1000: Copyright (c) 1999-2006 Intel Corporation.
>>>> Feb 20 05:52:56 cirroskern.info <http://kern.info> kernel: [ 0.770137] ne2k-pci.c:v1.03 9/22/2003 D. Becker/P. Gortmaker
>>>> Feb 20 05:52:56 cirroskern.info <http://kern.info> kernel: [ 0.772344] 8139cp: 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
>>>> Feb 20 05:52:56 cirroskern.info <http://kern.info> kernel: [ 0.781780] pcnet32: pcnet32.c:v1.35 21.Apr.2008tsbogend at alpha.franken.de <mailto:tsbogend at alpha.franken.de>
>>>> Feb 20 05:52:56 cirroskern.info <http://kern.info> kernel: [ 0.786775] ip_tables: (C) 2000-2006 Netfilter Core Team
>>>> Feb 20 05:52:57 cirroskern.info <http://kern.info> kernel: [ 1.112086] Refined TSC clocksource calibration: 3392.132 MHz.
>>>> Feb 20 05:52:57 cirroskern.info <http://kern.info> kernel: [ 1.680348] eth0: IPv6 duplicate address fe80::f816:3eff:fea2:6e02 detected!
>>>> ############ debug end ##############
>>>> cloud-setup: failed to read iid from metadata. tried 30
>>>> WARN: /etc/rc3.d/S45-cloud-setup failed
>>>> Starting dropbear sshd: generating rsa key... generating dsa key... OK
>>>> ===== cloud-final: system completely up in 5743.03 seconds ====
>>>> wget: can't connect to remote host (169.254.169.254): Connection timed out
>>>> wget: can't connect to remote host (169.254.169.254): Connection timed out
>>>> wget: can't connect to remote host (169.254.169.254): Connection timed out
>>>> instance-id:
>>>> public-ipv4:
>>>> local-ipv4 :
>>>> wget: can't connect to remote host (169.254.169.254): Connection timed out
>>>> cloud-userdata: failed to read instance id
>>>> WARN: /etc/rc3.d/S99-cloud-userdata failed
>>>> ____ ____ ____
>>>> / __/ __ ____ ____ / __ \/ __/
>>>> / /__ / // __// __// /_/ /\ \
>>>> \___//_//_/ /_/ \____/___/
>>>> http://launchpad.net/cirros
>>>>
>>>>
>>>>
>>>> login as 'cirros' user. default password: 'cubswin:)'. use 'sudo' for root.
>>>>
>>>> cirros login:
>>>>
>>>> Thanks for the help.
>>>>
>>>>
>>>> On 21 February 2013 08:33, Sylvain Bauza
>>>> <sylvain.bauza at digimind.com
>>>> <mailto:sylvain.bauza at digimind.com>> wrote:
>>>>
>>>> Le 20/02/2013 23:04, Chathura M. Sarathchandra
>>>> Magurawalage a écrit :
>>>>> Thanks.
>>>>>
>>>>> I would be more concerned about the
>>>>> SIOCDELRT error above. Do you try to
>>>>> manually remove a network route at bootup
>>>>> ? Seems like the 'route del' is failing
>>>>> because the route is not already existing.
>>>>>
>>>>> I am not doing doing anything that I am aware of.
>>>>>
>>>>>
>>>>> As already said, you absolutely need VNC
>>>>> support for investigating. Could you
>>>>> please fix your VNC setup which is incorrect ?
>>>>>
>>>>>
>>>>> But VNC works fine. Its just that it VM hangs
>>>>> on the boot up it wont come to the log in
>>>>> prompt, I can't log into it. :(
>>>>>
>>>>
>>>>
>>>> Ahuh. Sorry for bugging you, I haven't
>>>> understand : is your VM failing to boot up ?
>>>> Which distro is your VM based on ?
>>>>
>>>> From my POV, your console.log is fine : your VM
>>>> is booting, getting DHCP lease, trying to
>>>> contact metadata server, failing to contact it,
>>>> and that's it. You should get a prompt when
>>>> logging in thru VNC.
>>>>
>>>> Please clarify : either the VM is failing to
>>>> boot up properly (and then try to find a small
>>>> and cloud-out-of-the-box distro like CirrOS for
>>>> testing, or try with runlevel 3 or interactive
>>>> startup), or your VM is properly started
>>>> without network connectivity (and then you have
>>>> to login and try more diagnostic tools like
>>>> ping/tcpdump).
>>>>
>>>>
>>>> Thanks,
>>>> -Sylvain
>>>>
>>>>
>>>
>>>
>>
>>
>>
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.openstack.org/pipermail/openstack/attachments/20130222/2de05407/attachment.html>
More information about the Openstack
mailing list