Open Stack

Hi Geo, 
your packet will be sent out of br-tun via the gre-xxxxx port "pointing"
to your compute node. So what you have to do is to put the ip address to
your eth interface connected to the wire. The same of course on the
controller node. Putting the ip address on the br-tun does not make
sense, as it just hangs around without any physical port plugged in.

This is how my ovs-vsctl show looks like on the compute node.

ovs-vsctl show
9253a3f8-3c28-4953-ae85-ca94aa0d4fb1
    Bridge br-tun
        Port br-tun
            Interface br-tun
                type: internal
        Port "gre-c0a801ca"
            Interface "gre-c0a801ca"
                type: gre
                options: {in_key=flow, local_ip="192.168.1.190",
out_key=flow, remote_ip="192.168.1.202"}
        Port patch-int
            Interface patch-int
                type: patch
                options: {peer=patch-tun}
    Bridge br-int
        Port br-int
            Interface br-int
                type: internal
        Port patch-tun
            Interface patch-tun
                type: patch
                options: {peer=patch-int}
        Port "qvo1c352474-0c"
            tag: 1
            Interface "qvo1c352474-0c"
        Port "qvo5782980b-be"
            tag: 4095
            Interface "qvo5782980b-be"
    ovs_version: "2.1.2"



And this is the ip configuration of the net device used:

22: eth0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast
state DOWN qlen 1000
    link/ether 02:00:00:39:13:9a brd ff:ff:ff:ff:ff:ff
    inet 192.168.1.190/24 brd 192.168.1.255 scope global eth0
       valid_lft forever preferred_lft forever





And this is my ml2.conf on the compute node

[ovs]
local_ip = 192.168.1.190
tunnel_type = gre
enable_tunneling = True



Regards


-- 
Andreas 
(irc: scheuran)


On Wed, 2014-11-26 at 01:39 +0530, Geo Varghese wrote:
> Hi Team,
> 
> 
> 
> I need some help to setup instance tunnel.
> 
> 
> I tried 2 node installation today and successfully added new compute1
> node. 
> 
> Later i have created new VM on new compute1 node. It successfully
> spawned but the issue is it couldn't get dhcp ip.
> 
> Due to this eth0 is not assigned with an IP address. I think instance
> tunnel interface is not correct.
> 
> Currently I set IP to automatically created interface br-tun, do i
> need to create new instance tunnel?
> 
> =========================================
> br-tun Link encap:Ethernet HWaddr 6a:65:2d:ed:90:44 
> inet addr:192.168.123.179 Bcast:192.168.123.255 Mask:255.255.255.0
> inet6 addr: fe80::98c7:a1ff:fef6:bcd7/64 Scope:Link
> UP BROADCAST RUNNING MTU:1500 Metric:1
> RX packets:0 errors:0 dropped:0 overruns:0 frame:0
> TX packets:8 errors:0 dropped:0 overruns:0 carrier:0
> collisions:0 txqueuelen:0 
> RX bytes:0 (0.0 B) TX bytes:648 (648.0 B)
> =========================================
> 
> And given this Ip addres(192.168.123.179) in [mvs] configuration
> (/etc/neutron/plugins/ml2/ml2_conf.ini)
> 
> [ovs]
> local_ip = 192.168.123.179
> tunnel_type = gre
> enable_tunneling = True
> 
> Is it correct? Please help me.
> 
> 
> --
> Regards,
> Geo Varghese
> _______________________________________________
> OpenStack-operators mailing list
> OpenStack-operators at lists.openstack.org
> http://lists.openstack.org/cgi-bin/mailman/listinfo/openstack-operators