Open Stack

Continued with ConfigParser, nothing much difference apart from clean way
of maintaining INI file in iniparse. I think unless a solution is thought,
good to go with this.

Thanks again John.


On Mon, Jan 20, 2014 at 11:47 PM, John Griffith <john.griffith at solidfire.com
> wrote:

> On Mon, Jan 20, 2014 at 11:15 AM, John Griffith
> <john.griffith at solidfire.com> wrote:
> > On Mon, Jan 20, 2014 at 10:30 AM, iKhan <ik.ibadkhan at gmail.com> wrote:
> >> Thanks John,
> >>
> >> It worked earlier while executing because iniparse was installed, tho
> this
> >> wasn't present in virtual environment. Installing iniparse via pip did
> work.
> >> Since I didn't install iniparse specifically, I was under impression it
> was
> >> there by default. Probably now I have to take care of this in
> >> test-requirement.txt as you mentioned.
> >>
> >> I wonder if there is an alternative to iniparse by default.
> >>
> >> Regards
> >>
> >>
> >> On Mon, Jan 20, 2014 at 10:47 PM, John Griffith
> >> <john.griffith at solidfire.com> wrote:
> >>>
> >>> On Mon, Jan 20, 2014 at 10:07 AM, iKhan <ik.ibadkhan at gmail.com> wrote:
> >>> > Hi,
> >>> >
> >>> > I have imported iniparse to my cinder code, it works fine when I
> perform
> >>> > execution. But when I run the unit test, it fails while importing
> >>> > iniparse.
> >>> > It says "No module named iniparse". Do I have to take care of
> something
> >>> > here?
> >>> >
> >>> > --
> >>> > Thanks,
> >>> > Ibad Khan
> >>> > 9686594607
> >>> >
> >>> > _______________________________________________
> >>> > OpenStack-dev mailing list
> >>> > OpenStack-dev at lists.openstack.org
> >>> > http://lists.openstack.org/cgi-bin/mailman/listinfo/openstack-dev
> >>> >
> >>>
> >>> It sounds like it's not installed on your system.  You'd need to do a
> >>> "pip install iniparse", but if you're adding this to your unit tests
> >>> you'll need to have a look at the common test-requires file.  Also
> >>> keep in mind if your driver is going to rely on it you'll need it in
> >>> requirements.  We can work through the details via IRC if you like.
> >>>
> >>> John
> >>>
> >>> _______________________________________________
> >>> OpenStack-dev mailing list
> >>> OpenStack-dev at lists.openstack.org
> >>> http://lists.openstack.org/cgi-bin/mailman/listinfo/openstack-dev
> >>
> >>
> >>
> >>
> >> --
> >> Thanks,
> >> Ibad Khan
> >> 9686594607
> >>
> >> _______________________________________________
> >> OpenStack-dev mailing list
> >> OpenStack-dev at lists.openstack.org
> >> http://lists.openstack.org/cgi-bin/mailman/listinfo/openstack-dev
> >>
> >
> > there is check out openstack.common.iniparser, not sure if it'll fit
> > your needs or not.
> DOH!!  Disregard that
>
> _______________________________________________
> OpenStack-dev mailing list
> OpenStack-dev at lists.openstack.org
> http://lists.openstack.org/cgi-bin/mailman/listinfo/openstack-dev
>



-- 
Thanks,
Ibad Khan
9686594607
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.openstack.org/pipermail/openstack-dev/attachments/20140121/eacf63ed/attachment.html>